thunderlaser-nolan

Hi，thank you for your fancy,because the Chinese New Year,we just came back to work,I have sent the file for you,please check it,thank you.

Hi，thank you for your advise,I will try,I have sent the file for you,please check it,thank you.

Hi，thank you for your fancy,I have sent the file for you,please check it,thank you.

Hi,thank you for your fancy,because the Chinese New Year,we just came back to work,sorry to late reply for you,I have sent the file for you by message,please download it.

Hi，thank you for your fancy,because the Chinese New Year,we just came back to work,I have sent the file for you,please check it,thank you.

Today, I share with you some of the small problems we often encounter when using a machine.Warning of LCD panel.The alarm prompt of panel as follow:A. frame/X/Y slop overB. No enough extend spaceC. Water errorD. Machine protectedA. Frame/X/Y Slop overLCD panel shows the following information:Here are the reasons:① the size of the graphic is larger than the working area of the machineIf your laser cutter’s working area is 600 x 400mm, but you want to cut a graphic which larger than 600 x 400mm, this warn appears. Since the laser is not able to work beyond its working.② incorrect starting pointIf you set an incorrect starting point, the graphic might be out of bounds. Please set a correct starting point to resolve this problem as the below pic③wrong pulse settingIf you set wrong pulse…

Today, I share with you some of the small problems we often encounter when using a machine.Warning of LCD panel.The alarm prompt of panel as follow:A. frame/X/Y slop overB. No enough extend spaceC. Water errorD. Machine protectedA. Frame/X/Y Slop overLCD panel shows the following information:Here are the reasons:① the size of the graphic is larger than the working area of the machineIf your laser cutter’s working area is 600 x 400mm, but you want to cut a graphic which larger than 600 x 400mm, this warn appears. Since the laser is not able to work beyond its working.② incorrect starting pointIf you set an incorrect starting point, the graphic might be out of bounds. Please set a correct starting point to resolve this problem as the below pic③wrong pulse settingIf you set wrong pulse setting for the motors, it might cause this problem too. Please correct the pulse setting as the following case:http://www.thunderlaser.com/troubleshooting/laser-cutter-has-a-wrong-cuttingengraving-size.htmlOr wrong setting as following link: http://www.thunderlaser.com/troubleshooting/wrong-proportions-from-software.htmlB. No enough extend spaceLCD panel shows the following information:This problem only appears on engraving mode, it’s caused by the buffer distance is out of bound. For example, if you want to engrave a picture of 200 x 200mm, you move the laser head to the top left corner of the working table and press the ‘origin’ to set the starting point. When you press the ‘start’ button to start engraving, the failure warning would appear.How to fix this problem?Press ESC at first, and then move laser head to right distanc to leave enough buffer distance. Now set a new starting point by pressing the ‘origin’, you will find the problem was fixed when you run the job again.Why this happen?When the machine is engraving in high speed, the actual moving distance of the motor is usually larger than the graphic. Therefore, we need to keep enough buffer distance on the two sides of the graphic. The buffer distance will be longers as long as you set faster speed, so we need to keep more buffer distance when the speed is higher.(buffer distance within the working table)C. water errorLCD panel shows the following information:Forgot to turn on water chiller（water pump） or without connection for signal line.Please turn on the water chiller before open the machine and make sure the signal line is connective.D. machine protectedLCD panel shows the following information:Here is the reason:Our machine have sensor for flap protection（top-front/top-rear flap）as following:Please close all the top flap before start to work.

I don't know how to upload the file, I uploaded it clearly, but I don't know why I couldn't find it, I can send it to you if you need it.

DXF file or CAD

Of course, I will continue to update, thanks for your advice

About laser cutter Maintain:Maintenance of the machine is generally maintained in the following four aspects:A.Lens and mirror: ① Focus lens (please clean after use) ② Reflector (please clean then once a week) ③Laser combiner(please clean once a week)B.Rails and screws：①X/Y axis Rails（please add oil once a month）②Z axis Screws（please add oil once a month）C. Laser path：①when the laser head move to four corners of the working table, check if the laser beam to the same position on the third reflective mirror.②when the laser head moves to four corners of the working table, check if the laser beam can vertically go through the acrylic.（please check once a month）D. water chiller:①cooling water（please change once a month）②filters（please clean once a month）