Introduction: CS3 Knex Shotgun
Compact Shotgun 3
A mid ranged, double barreled shotgun pistol. Each barrel holds three blue rods. The barrels can be fired individually or simotaneously. The CS3 fixes all of the CS2's structural problems.
Version History
2: CS3
3: CS2
4: CS1
Influences
DsMan- trigger
CS3 Music Video
www.youtube.com/watch
Step 1: Part Count
 |
I've got a parts list!
Rods
9 yellow
14 blue
16 white
30 green
2 long black
Connectors
15 green
17 orange
10 red
29 yellow
5 gray 2 slot
7 gray 1 slot
7 tan
2 Y
Miscellaneous
2 female ball joint connectors
1 T connector
4 hinges (2 male and 2 female)
21 blue spacers
6 gray spacers
Step 2: Handle
1: Build three of these.
2: Attach with a blue rod and a gray rod as shown.
3: Build this.
4: Build this.
5: Build this.
6: Attach parts 3-5.
7: Attach all parts.
8: Build this.
9: Attach as shown.
10: Add a tiny elastic as shown.
Step 3: Barrels
Gather these parts for step 1:
8 blue spacers,
4 gray spacers,
6 orange connectors,
2 tan connectors,
4 gray connectors,
8 yellow connectors,
4 black connectors,
4 blue rods,
1: Build this.
2: Gather these.
3: Attach as shown.
4: Build this.
5: Attach as shown.
6: Build this.
7: Slide on as shown.
8: Gather these.
9: Attach as shown.
10: Add two gray rods as shown.
11: Build this.
12: Attach as shown.
Gather these parts for step 13:
5 yellow connectors,
4 red connectors,
2 tan connectors,
2 yellow rods,
2 gray rods,
4 green rods,
6 blue spacers,
13: Build this.
14: Attach as shown.
Step 4: Trigger
1: Build this.
2: Build this.
3: Attach as shown.
4: Build this ( the cut rod is optional but will allow more elastics to be placed on the firing rods).
5: Attach as shown.
6: Build these.
7: Slide in a yellow rod as shown.
8: Attach the parts from picture 6 as shown.
Step 5: Assembly
1: Build this.
2,3: Attach the part from step 1, the handle, trigger, and barrels as shown.
Step 6: Finishing Up
1: Build two of these.
2: Add duct tape to the firing rods as shown.
3: Add firing and trigger elastics as shown.
Step 7: Loading and Firing
These are instructions from the CS2 instructable, it loads and fires the same way.
Cocking:
1: Pull back the bottom firing rod.
2,3: With your hand pressing up on the trigger mechanism, pull back the top firing rod.
Loading:
4: Hold three yellow rods as shown.
5: Insert them into the top barrel.
6: Push them all the way in.
7: Insert three more into the bottom barrel.
Now pull the trigger!
Step 8: Finished!
Have fun and don't forget to rate!
Step 9: Trouble Shooting?
Contact me.
Be the First to Share
Recommendations
Organization Contest
Plastic Challenge
Robots Contest
101 Comments
9 years ago on Introduction
Wow. The rubber bands at small.
9 years ago on Introduction
Mine trigger doesn't work
11 years ago on Step 4
WTF?!? Is that another 8 hinges? I counted out EVERY peice only to find I dont have enough!
Reply 10 years ago on Introduction
ikr i did the same thing and ended up thinking wtf is a t connecter and just found out i don't have that or hinge pieces!
11 years ago on Introduction
Ich habe einen schrumpelich spitzbart... lol german someone translate it... =D
Reply 10 years ago on Introduction
it says
I have one schrumpelich pointed beard
lol
Reply 10 years ago on Introduction
LOL!
Reply 11 years ago on Introduction
I have a goatee schrumpelich???? xdxdxd
Reply 10 years ago on Introduction
nice try! it means "I have A Wrinkled Goatee beard"
L0L
Reply 10 years ago on Introduction
whaha thats an awesome word :P
10 years ago on Introduction
what kind and how many bands did you use?
11 years ago on Introduction
wow CS3 vs CS1 is a big difference, nice job 5*
Reply 11 years ago on Introduction
i made it 5.00 :D
11 years ago on Introduction
Can I use a small blue one-way connector instead of the tan one-way connectors on all the steps? Since I have very little tan pieces but alot of the one-way blue connectors that are just like the tan ones.
Reply 11 years ago on Introduction
Also does anybody know how to make a safety for any gun? Since one time I made a crossbow and it went off by accident and hit my mom in the glasses... I don't want that to happen with the gun. I always point the gun down to the ground with two hands when I'm not using it but I still my go off by accident.
Reply 11 years ago on Introduction
rofl!
Reply 11 years ago on Introduction
Yes, you should be able to.
11 years ago on Step 3
I'm all right I replaced it now
11 years ago on Step 3
whoops caps lock was on
11 years ago on Step 3
ON STEP FOUR CAN I CHANGE BALL SOCKET FOR SOMTHING ELSE