AlessandroG2

yes, but do not forget to run your own autopid and step/mm calibration, as explained at the end of this instructions:https://drive.google.com/file/d/1tsXY2cl3d77rsc1SDjsuuNOrL5W1tXiu/view?usp=sharingI've also added my mod to CR10 standalone, removing the standard board case.

HI MUsaw,what do you mean in step "calculate the gap from the default position 1500?"Is not clear to me how should I adjust the trimming valuesthanks

Hi, sorry i'm not sure of exact latency measure, but it seems almoust realtime to me

look very nice! I was wondering to improve the web control interface, this could be a very good choice! Thank you

anche originale

Si installa sia il sistema operativo che octoprint, la comodità dell'immagine gia preparata è che molti settaggi son già fatti in questo modo. Per la camera, basta una webcam usb, io uso una logitech

Se usi l'ultima versione di cura puoi interfacciarla direttamente con octoprint e premere stampa direttamente da cura, con le versioni piu vecchie invece debi fare manualmente l upload del file gcode generato da cura un octoprint, ma funziona lo stesso.

Con Cura non puoi, cura manda solo il gcode dello slicing dei modelli 3d ma non ci comandi la stampante direttamente per questi settaggi. io ho usato sempre Repeteir o Octoprint. Ma qualsiasi software equivalente va bene, dipende anche dalla tua stampante e i relativi driver per connettrla al pc

Ti riferisci ai comandi del punto 5? Da qualsiasi programmi usi per comandare la stampante, io uso Octoprint su Raspberry.

Ciao, dovresti riuscire a calibrare la distanza del piatto riscaldata all estrusore agendo semplicemente sulle manopoline sotto il letto stesso che comprimono o meno le molle. Sposti l estrusore nei 4 angoli e aggiusti l'altezza, usando sempre un A4 come riferimento, girando in senso orario /antiorario le manopole in modo da avvicinare o allontanare il letto in base all esigenza.

The capacitor is visible in the right picture, close to the blu wire, that connects the two Arduino pins RESET and GND.

you're welcome

right today I was finally able to flash and have it works using as board esp8285 instead of esp8266 or the Arduino IDE. Try if it works also for you

Hi,followed this instruction, Arduino IDE says [100% ] uploaded, so I have disconnected my board from FTDI and PC and connected it to AC...but nothing happens, no led blinking; same thing with 2 different board; what i'm missing? can you help?

can you share the code?

Hi Oliver, how did you connected and configured the led ring?

Hi !!! I have my Alexa on RP3 running for all general questions, but each time I say Alexa trigger XXX she says "sorry I can't see this IF trigger", did it happened to you?Secondary, did you figured out how to aumatically starts alexa at boot?

Hi !!! I have my Alexa running for all general questions, but each time I say Alexa trigger XXX she says "sorry I can't see this IF trigger", did it happened to you?

Hi gavinvonk, thank you for your reply:This is my mic:"Sienoc Super mini USB 2.0 Mic USB Plug for Skype Msn Video Win 7 Win8" (http://amzn.eu/deFoQCJ)I will post the log later as soon I will be near my Pi :-)

here the error

Hi gavinvonk, I have an error with pulse audio during Alexa service startup, even if it says that alexa is running in all my devices. I have tested audio by command lines, and it works for listening and recording, but alexa doesn't starts. What can i do?

hi Toglefritz, can i use TowerPro MG996R instead of Hitech like in your pictures above?

HI,uStepper OPTIONAL means that I can use even other boards to control the arm, in this case I should write my own sketch right?

HI OWENlab!!!Can you please upload a more "detailed" list of the mechanical parts?I see many more parts on the pictures than the BOM section and I'm afraid I'm missing some parts on my shopping cart