rich.altmaier's instructables
Achievements
- rich.altmaier commented on rich.altmaier's instructable Triple Mango Cake12 days ago
- rich.altmaier's instructable Mango Eclair With Raspberry Glaze's weekly stats: 6 weeks ago
331 views0 favorites4 comments
- rich.altmaier commented on rich.altmaier's instructable Mango Eclair With Raspberry Glaze6 weeks agoView Instructable »
Making these is enough steps that it is more fun to make with a partner! Post photos!
- rich.altmaier commented on rich.altmaier's instructable Mango Eclair With Raspberry Glaze6 weeks agoView Instructable »
If you think mango may be interesting, check out my Triple Mango Cake!thanks!Rich
- rich.altmaier posted an instructable Mango Eclair With Raspberry Glaze7 weeks ago
- rich.altmaier commented on stuarthayden10's instructable Replace a Cat5e Connector8 weeks agoView Instructable »
Stuart, I strongly recommend using a "load bar" to pre-order and align the wires! Night and day improvement. https://www.digikey.com/product-detail/en/cinch-connectivity-solutions-aim-cambridge/32-2198UL/J10091-ND/2096753?&gclid=EAIaIQobChMI-fvRv_Tv3gIVYRh9Ch3uLAJjEAQYASABEgIVpvD_BwE
- rich.altmaier commented on dobataloud's instructable 3D Printed Doweling Jig With Attachments2 months agoView Instructable »
Hi, i don't see any 45 degree angle in any of your components. Could you add a photo of that? How do you get the guide on a 45degree angle, with some support?
- rich.altmaier commented on rich.altmaier's instructable 3D Printed 50psi Water Pressure Vessel 2 months agoView Instructable »
Shihaba7, I think not because air gets through much smaller holes than water. Here is a paper on the topic: http://sensistor.com/wp-content/uploads/2015/05/Me...That said, I look forward to your posting your results!
- rich.altmaier commented on Disc Dog's instructable Tiny Shipping Container Home4 months agoView Instructable »
Regarding "...PLEASE look into zoning regulations before you make the final location decision; not all areas are modular or shipping container home friendly."Could you name any nearby suburban cities which will permit this structure? I think there is quite a challenge in the building permit. In fact this contest really should be about obtaining a building permit for a tiny home.
- rich.altmaier commented on tobychui's instructable A Raspberry Pi NAS That Really Look Like a NAS5 months agoView Instructable »
A very nice design, good work! I have a suggestion to do a similar design but use the Intel NUC. I used the Pi for a year as a server, and the darn thing would hang every few weeks. I think the quality level of Raspberry Pi is not up to any server standard. Go with the NUC!
- rich.altmaier followed lingib7 months ago
- By lingib
- rich.altmaier enrolled in Beginner 3D Printing Class7 months ago
- rich.altmaier's instructable 3D Printed 50psi Water Pressure Vessel 's weekly stats: 11 months ago
- 216 views4 favorites0 comments
- rich.altmaier posted an instructable 3D Printed 50psi Water Pressure Vessel 11 months ago
- rich.altmaier's instructable 3D Printing a Curved Shell for a Teapot Handle's weekly stats: 1 year ago
- 387 views2 favorites3 comments
- rich.altmaier commented on rich.altmaier's instructable 3D Printing a Curved Shell for a Teapot Handle1 year agoView Instructable »
PLA is rated to 170C, which is 338F. So boiling water is way below that. So far, so good!
- rich.altmaier entered Triple Mango Cake in the Baking Contest 2017 contest 1 year ago
- rich.altmaier posted an instructable Triple Mango Cake1 year ago
- rich.altmaier posted an instructable 3D Printing a Wraparound Shell for a Teapot Handle1 year ago
- rich.altmaier commented on JohanL39's instructable 3D Printed Water Motor1 year agoView Instructable »
Is the water chamber watertight? Is there any leaking? Does it leak if the exit is capped?
- rich.altmaier enrolled in 3D Scanning Class1 year ago
- rich.altmaier commented on electronics for everyone's instructable Bluetooth Door Lock (Arduino)2 years agoView Instructable »
Please be aware there is no security in this solution, in that any random person can walk up, pair, and open the door. So you can consider this lock the equivalent of no lock at all. It looks like a fun project! But for a real door, it would be cheaper and equivallent security to have no lock at all.
- rich.altmaier favorited Seismometer by 10DotMatrix2 years ago
- rich.altmaier commented on Imetomi's instructable Bicycle Cell Phone Charger (Wind Turbine with build in Battery)2 years agoView Instructable »
I'm sorry but this is not going to work. The energy generated is way way too small to put any measurable charge on a phone.
It is quite lovely. The color is my favorite aspect!