.223 Ammo Pin

4,897

64

17

Introduction: .223 Ammo Pin

About: Awesome Gear I've designed myself.

I’m not a gun nut but I still think this pin is cool. I put it on my camping bag but you could put it on a hat, jacket, or make it a tie tack. Just don’t take it through an airport =).

To make it:

Use an expended cartridge. That means a bullet that has already been shot. Do not under any circumstances use live ammo.

Mount an empty shell in to a drill press. Make sure it is on it’s lowest RPM. Use a pipe cutter to cut off the primer end. File the back side flat.

For the pin part I got a pack of “pins and clutches” from the craft store; 10 for $3.00. Cut the pin out of the backing. Mount it into a drill press and file it down until it fits into the hole in the back of the shell.

Place a piece of solder into the shell. Heat it from the bottom so the solder seeps into the hole. While the solder is molten, place the pin in the hole. File away any excess solder.

To polish the completed pin use 1000 grit sand paper followed by polishing compound and a polishing wheel.

Be the First to Share

    Recommendations

    • Maps Challenge

      Maps Challenge
    • Summer Fun: Student Design Challenge

      Summer Fun: Student Design Challenge
    • Fruit and Veggies Speed Challenge

      Fruit and Veggies Speed Challenge

    17 Comments

    0
    ginger snaps
    ginger snaps

    9 years ago on Introduction

    These look great! Can someone tell me where they get the empty shells from I can't wait to make some!

    0
    weaponsmaster18
    weaponsmaster18

    Reply 4 years ago

    its easy jut find someone who likes to shoot and doesn't reload theyd probably be happy to give you their brass unless they know a gunsmith like I do who will give u a certain amount off on ammo if you bring in your brass to him. for reloading

    0
    mr.mountaineer
    mr.mountaineer

    Reply 9 years ago on Introduction

    i bought mine at a flea market. they were being so you can reload them. i got about 200 3030, 30-06and 8mm . but you can probably get some at a gun range if you ask and they would probably sell them to you pretty cheap if not give them away

    0
    Pwag
    Pwag

    10 years ago on Introduction

    Thanks for the great idea man. I made four of these. They are awesome and will make some great gifts! I took mine and slathered them with india ink before I polished them.

    This left the ink in the writing and poor which gave it a nice antiqued look.

    Thanks again!

    284204749.jpg
    0
    Mrballeng
    Mrballeng

    Reply 10 years ago on Introduction

    This is all kinds of awesome. Looks Great! And thanks for posting photos.

    0
    RedneckEngineer

    Now if you could make these into snap buttons for a hunting jacket that would look real good. I wonder if shotgun shells would make nice size buttons?? Hummmm

    0
    Mrballeng
    Mrballeng

    Reply 10 years ago on Introduction

    I've made a pin from a shotgun shell as well. It's easier then the rifle shell. I like your thinking. I don't own a hunting jacket or even go hunting but I'm going to have to figure out how to make a button that can be fitted over existing snap buttons. Thanks for the ideas!

    0
    RedneckEngineer
    RedneckEngineer

    Reply 10 years ago on Introduction

    Well you keep on a making and I'll keep on thinking! I love what you been putting on here so far, keep um comin!

    0
    thematthatter
    thematthatter

    Reply 10 years ago on Introduction

    You would think that would be common sense but I saw a safety message where someone used the business end of a 50 cal round as a hammer... Unsuccessfully.

    0
    Mrballeng
    Mrballeng

    Reply 10 years ago on Introduction

    Yikes!!!! I'll have to add that. But yes, EXPENDED CARTRIDGES ONLY!!!

    0
    SWV1787
    SWV1787

    10 years ago on Introduction

    I like this alot. I know someone who tried to incorporated a spent 30-06 cartridge into their fashion by gauging their ear and then sticking the cartridge in the hole... They got an infection from the brass. I think your method seems alot safer. I will prob be making a couple dozen of these out of .45 shells next time I go the the range.

    0
    Mrballeng
    Mrballeng

    Reply 10 years ago on Introduction

    I once made valve stem caps for a buddy's truck tires with 40 cal shells. With the right size plastic cap you can simply press the shell right on.

    0
    CrLz
    CrLz

    10 years ago on Introduction

    Sweet! My dad used to make the same from 30-06 casings. Now I can try my own!