Sonic Adventure 2: Space Colony ARK Mini

Now, while i was making [SC ARK], i thought about you guys that did'nt have enough peices to build this, so i built SC ARK Mini, which needed little peices. Then i saw that it could be a 3-in-1, then i realised, it already was! It:

Folded away for in my pocket
Acted as spinning top (barely)
and was a model of ARK

Other Models Availible:

Full Version SC ARK:
https://www.instructables.com/id/Sonic-Adventure-2-Space-Colony-ARK/
Chaos Emerald Control Panel:
Not availible yet

To Make SC ARK Mini, Here is what you need:
Rods:
8 White rods
1 Blue rod
8 Green rods

Connectors:
5 Grey Connctors
8 Light Grey Connectors

and thats it! told you it needed little peices!

NOTE: Surface of SC ARK Mini is not round but strait. The spinning top mode does not last very long. Folding up must be done carefully, as not all peices are connected.

Teacher Notes

Teachers! Did you use this instructable in your classroom?
Add a Teacher Note to share how you incorporated it into your lesson.

Step 1: Base of ARK Mini

Ok, lets get started!

1. Nothing really
2. Build These
3. Put them on and twist one

Sonic = "Huh, No problems"

Step 2: Core of ARK Mini

Nothing

1. Build This
2. Put through hole on base

"Huh, again, No problems"

Step 3: Finishing Off

Nothing Special about this step

1. Put grey clip on the end of the blue rod
2. twist white rods upward.

Now, was that easy or what!?

Step 4: Finishing Off P2

ok, so youve finished, "Now what do i do?" you might ask, well, you have two options:

A. Learn how to fold it up. Next Step
B. Learn how to turn it into a spinning top (doesn't spin for long, but you knew that if you read the note) step 6

Please comment on eaisy my instructable is and how i can make it eaisier. thanks

Step 5: Folding It Up

Pritty easy.

1. Take end cap off
2. Take Core out
3. Twist downwards
4. Put end cap back on blue rod, and youre done.

Eggman = "ha ha ha, peice of cake"

Step 6: Spinning Top Mode

Simple, follow steps

1. Remove Grey clip
2. Take out Core
3. Twist the rods down
4. Remove grey clips like shown
5. Put rod through hole
6. Top side veiw
7. Bottom side veiw

Done! now reverse these steps to turn it back into SC ARK Mini.

Have Fun with your new mini model of ark!

Be the First to Share

    Recommendations

    • CNC Contest

      CNC Contest
    • Teacher Contest

      Teacher Contest
    • Maps Challenge

      Maps Challenge

    13 Discussions

    0
    None
    mrbox

    11 years ago on Introduction

    Well I had it back in 2001 and i didnt even know back then there was a gamecube, and i bought it so i could play grandia =)

    1 reply
    0
    None
    mrbox

    11 years ago on Introduction

    Ahh old times every1 would come to my house just cause i had a dreamcast ahh good times =)

    1 reply
    0
    None
    ultimatesx9mrbox

    Reply 11 years ago on Introduction

    dreamcast was good, glitchy, but good. theres two things i dont like about it tough, 1. It was sega's last console. 2. Quite a few games were very glitchy, sonic 2 for example. 3. Its like nothing compared to the gamecube. security copyrighting emulators for it

    0
    None
    flames10391

    11 years ago on Introduction

    lol the other one is okay but this ive made before not thinking lol