Introduction: DD-KYT

About: I like shooting paper targets with just about anything and i like showing off. :)

The name of the gun is pronounsed the DD-Kite combat pistol
A gun I started working on a while ago. It was scrapped because of flimsyness, but is now back with some new mods!

Accurate at close range
Hop up (from the TDS2 by the dunkis)
True trigger (from Dsmans sidearm by Dsman1)
Looks good
removable mag and handle mag.

Sometimes jams
A bit bigger than other sidearms.
Bad trigger pull!

I would like to say thanks to every one who will help mod this gun and perfect it and to every one who I took parts from (more indepth credits will be at the end):
(everybody else I forgot!)
Proceed to next step!

Step 1: The Barrel

Here i will show you how to make the barrel of this amazing pistol!

Pic 1: Make this.
Pic 2: and this.
Pic 3: Connect them together.
Pic 4: Another view.
Pic 5: Gather these.
Pic 6: Put them on like this.
Pic 7: Another view.
Pic 8: Gather these.
Pic 9: Attach like this and get 3 green rods.
Pic 10: Attach like this.
Pic 11: Gather these.
Pic 12: Attach them like this.
Pic 13: Another view.
Pic 14: Another view.

Step 2: Handle

I will now show you how to make the handle!

Pic 1: Make these.
Pac 2: Attach like this.
Pic 3: And this.
Pic 4: Gather these.
Pic 5: Attach like this.
Pic 6: Attach like this.
Pic 7: Attach like this.
Pic 8: Put theme here.
Pic 9: Gather these.
Pic 10: Put them here.
Pic 11: And here.

Step 3: Ram, Trigger, and Mag Pusher

Small pieces that make the gun functional.

Pic 1: Gather these pieces for the mag pusher. (look at the notes on the pics!)
Pic 2: Here is a close up of the moded piece.
Pic 3: Make this....
Pic 4: Or this.....
Pic 5: Gather these for the trigger.
Pic 6: Put these together like this.
Pic 7: Add these.
Pic 8: Ram.
Pic 9: Close up.
Pic 10: Put on some tape!
Pic 11: Gather these pieces.
Pic 12: Make sure its broken. (you could also use a tan clip...)
Pic 13: Put them together like this.
Pic 14: Put them on the barrel.
Pic 15: Add this part too!


Step 4: Add Ons

These include the hop up mech and the top part of the barrel. *optional*

Pic 1-7: The Top bart of the barrel
Pic 8: Gather these for the hop up.
Pic 9: use some of the pieces to make this and put them aside.

Step 5: Put It All Together!

How to put the gun together!

Pic 1: Take this blue connector off.
Pic 2: Put it here.
Pic 3: Click it on.
Pic 4: Put on these 2 one slot connectors.
Pic 5: Put in the trigger.
Pic 6: Put in a yellow rod.
Pic 7-9: Attach one slot connectors.
Pic 10: Ram rod.
Pic 11: Attach those hop-up pieces
Pic 12: Attach the actual hop-mech.
Pic 13: Make this.
Pic 14-15:Attach it here to lock hop-up in place
Pic 16: The top barrel.
Pic 17: Attach it like this!

Proceed to credits/loading.....

Step 6: How to Load the Gun and Credits.

To load the gun you can stick in a variety of ammo.
MAIN: Normal one slot connectors. (TDS ammo)
MAIN2: Ball socket connectors with black hands at the end.

Prototype: 2 black hands put together. (small shotgun affect)
Prototype2: 5 black hands down the barrel, ram rod pulled back ALL the way. (MASSIVE SCATTER!)

If you use the main ammo or prototype 1 ammo just put it in the mhandle and slide in the mag pusher.

If you use Prototype 2 ammo. just stuff them down the barrel.


DsMan and his Sidearm: https://www.instructables.com/id/DSman1s-sidearm
TheDunkis and his Tds: https://www.instructables.com/id/Knex-Pistol-TDS/
Tds2: https://www.instructables.com/id/TDS2/

Dont forget to rate and give plenty of feedback!
Thanks Instructablers!

Be the First to Share


    • Mason Jar Speed Challenge

      Mason Jar Speed Challenge
    • Pumpkin Challenge

      Pumpkin Challenge
    • Bikes Challenge

      Bikes Challenge

    31 Discussions


    11 years ago on Introduction

    fyi the trigger falls off.... ALOT you should streghten it


    Reply 11 years ago on Introduction

    really? Even though i haven't used the gun in a while, i think it didn't fall off very often. Are you sure you built it correctly? If you did then tell me if you find a way to fix it. Thanks.


    Reply 11 years ago on Introduction

    When I built it the conneten from the trigger to the gun was not very good add more than one conneten point. TE-HE!


    11 years ago on Step 5

    you added pieces on your gun but there aren't any step to do that... like where does the trigger attach?

    What I like about this gun is the angled handle, just right. It's also a cool, compact design. BTW: Sharpening black rods is a REALLY BAD IDEA (If you only have 2 of them) lol.


    Reply 11 years ago on Introduction

    I bought more. Now i have 8. I made a new DD-Kyt. Its much better, WAY less jamming, WAY better trigger pull, The Dunkis's flip up sights, and still has a hop up. The bad thing is, that its a bit bigger and heavier, and its more delicate (the sights)


    Reply 11 years ago on Introduction

    oh wait its on youtube...Well if you have instructions THEN post :)


    Reply 11 years ago on Introduction

    how do you load in the handle or what????????????????????????


    11 years ago on Introduction

    Btw, what exactly did you take from any of my guns and put on this? Lol.


    Reply 11 years ago on Introduction

    Trauts and Yerjoking will help process this gun and make it ready for the knexpert tourney.


    11 years ago on Introduction

    You can't really expect people to follow a comment template mate.


    Reply 11 years ago on Introduction

    i know i just kinda forgot to erase that! It was supposed to make it easier LOL